Page 8 - DatacomTools 2016 Catalog

Net Prowler Cabling and Advanced Network Tester

Identify, monitor, and correct LAN issues
Tests 10/100/1000 Base-T, IPV4/IPV6, VLAN, DHCP and more
The Net Prowler™ Cabling and Advanced Network Tester takes all the features and functionality of the Cable
Prowler™ and adds the capability to identify, monitor, and troubleshoot LAN issues associated with physical
layer and link conditions in the network.
- Supports IPV4 and IPV6 protocols
- Verifies DHCP connectivity and DNS
- Pings IPV4, IPV6, and URL addresses
- CDP, LLDP, NDP, and VLAN detection
- TCP/UDP Throughput Test
- Detects presence of PoE and class of PoE per IEEE 802.3af/at with load test for voltage drop
- Detects and reports current link speed and link capabilities for active Ethernet drops up to 1 Gbps
- Link light to identify location on a hub/switch/router port
- Tests CAT3/5e/6/6a Ethernet cable configuration and verifies connectivity while conducting tests for opens,
shorts, miswires, split pairs, and reverses
- Supports up to 8 testing and ID remotes for network & telephone cables
- Supports up to 20 network and coax ID-only mapping remotes
- Ability to define Network test name, cable name, save and print all results (cable testing & network testing)

Measurement Time Domain Reflectometry (TDR) Save Test Results Stores up to 250 Cable or network tests with user
Technology defined names
Cable Measurements Cable Testing and ID: up to 1000 ft Tone Generation Tone Frequencies: 730 Hz and 1440 Hz
Split Pair Detection: 3 ft to 1,000 ft Languages English, French, Spanish, German, Italian
Length Measurement: 0 to 1,500 ft ± (5%+1ft) Battery Life For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline
Supports 8 continuity and ID number remotes battery:
Supports 20 RJ-45 & 20 F-connector ID only remotes Operating – 20 hours typical
Power over Ethernet Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus) Standby – Life of battery (20uA max)
compliant PoE Batteries are included
Loads cable up to 25.5 watts Altitude 10,000 ft (3048 m) operating
(at class 4) Identifies Mode A or B (pairs with PoE) Temperature Operating: 32 to 122°F (0 to 50°C)
Active Ethernet Indicates advertised speeds of 10/100/1000base-t Storage: -22 to +140°F (-30 to 60°C)
half or full duplex Humidity 10 to 90% non-condensing
Can Link to network at 10/100base-t Enclosure High-strength PC/ABS plastic with V0 rating & boot
Maximum Voltage Parameters refer to the maximum voltage that can Withstands 4 foot drop on to concrete
be applied to any 2 connector pins without causing Size 1.85”H x 3.6”W x 6.8”L (4.7 x 9.15 x 17.3 cm)
Safety Compliances CE
damage to the tester. Weight with Batteries 1 lb 2 oz (510 g)
• RJ Jack: 66 Vdc or 55 Vac Warranty 1 Year
• F-connector: 50 Vdc or Vac

NP700 Net Prowler with 1-5 coax remote & 1-5 network ID only remote set in hanging T3 pouch $693.45
NP750 Net Prowler width 1-5 coax remote, network ID only remote set, 1-8 network, & telephone testing/ID remote set in a large T3 pouch $835.95
NP800 Net Prowler with 1-20 coax remote, 1-20 network ID only remote set, 1-8 network, & telephone testing/ID remote set in a large T3 pouch $854.95

Snap Shot Cable Fault Finder

Accurately finds cable length, impediments in the cable and conditions at the end of every wire in your data,
power, or communications/video system up to 3,000 ft.

With the complexity of today’s electrical, data, voice and video signal carrying systems, you need a cable fault
locator time domain reflectometer tool that is fast, accurate and easy to use to see down the wire and show
the exact conditions that exist. Snap Shot™ is that tool. Made in America with American Spread Spectrum Time
Domain Reflectometry technology, Snap Shot™ is the new 21st century tool for cable fault location for every
type of cable in any industry. Advanced Spread Spectrum TDR technology works in all wire environments and is
immune to voltage, current, or data stream disruptions. See the true picture of your wiring and cable systems
with the Snap Shot™ cable fault detector and length measurement tool today.

- Works on energized cables SSK250
- Finds cable length or distance to fault from one end Snap Shot Main
- Measures cable distance on spool Unit with CA001,
- Accuracy of 1% or better CA002, CA003,
- Calibrates NVP values AD001, AD002,
- Internal memory for storing most used NVP values TP200 and CP100
- Large backlit LCD display
Snap Shot - Built-in tone generator for cable tracing & identification
- Loop test for continuous testing
See it in action! - Displays length reading in feet or meters
- Auto-off to preserve battery life

SS200 Snap Shot Main Unit with CA001, CA002, CA003, AD001 and AD002 $194.70
SSK250 Snap Shot Main Unit with CA001, CA002, CA003, AD001, AD002, TP200 and CP100 $263.95

8 Click here to view Cable Testers

Datacomtools.com TM Free Ground Shipping on Orders over $99.00. In the contiguous states, certain items may not apply